新闻动态
全自动造型机发生震击无力
全自动造型机发生震击无力或不震击有如下几种原因：
There are several reasons why the automatic moulding machine is weak or not.
1、全自动造型机故障检测遇到空气滤清气堵塞，由于真空泵工作过程产生一些水份，长时间加上管路中一些异物便将空气滤清气中的滤芯堵死，压力表此时看着压力不小，但空气流量不够，造成机器震击无力。
1. The fault detection of automatic moulding machine encounters air filter blockage. Because of the water produced during the working process of the vacuum pump, the filter element in the air filter will be blocked by adding some foreign bodies in the pipeline for a long time. The pressure gauge looks at the pressure at this time, but the air flow rate is not enough, resulting in the weak shock of the machine.
2、由于长时间震动，会出现以下造型机故障：联接震定台与震击活塞的6条M20内六角钉松动，使震台与活塞之间有间隙，工作气流从此处泄漏，造成震击无力，特别是压实后不能震击。
2. Due to the long time vibration, the following faults will occur in the moulding machine: the six M20 internal hexagonal nails connecting the shaking table and the piston are loosened, which makes the gap between the shaking table and the piston, and the working air leakage from here, resulting in the weakness of the shaking, especially after compaction.
3、活塞与泵铁之间不润滑，发生锈蚀，也可造成震击无力，解决造型机故障，可打开通往震实台的橡胶管，注入一斤左右的煤油或山刷房 保定强夯 卷扬式启闭机 保定网站制作 收费岛模具 遮阳网 麻绳汽油，然后上好，开机震击，这时震击的声响会有很明显的变化。
3. There is no lubrication between piston and pump iron, and rust occurs. It can also cause shock weakness. To solve the problem of the moulding machine, the rubber pipe leading to the shock table can be opened, kerosene or gasoline can be injected into it, and then the sound of the shock will change obviously when the piston and pump iron are not lubricated and rusted
There are several reasons why the automatic moulding machine is weak or not.
1、全自动造型机故障检测遇到空气滤清气堵塞，由于真空泵工作过程产生一些水份，长时间加上管路中一些异物便将空气滤清气中的滤芯堵死，压力表此时看着压力不小，但空气流量不够，造成机器震击无力。
1. The fault detection of automatic moulding machine encounters air filter blockage. Because of the water produced during the working process of the vacuum pump, the filter element in the air filter will be blocked by adding some foreign bodies in the pipeline for a long time. The pressure gauge looks at the pressure at this time, but the air flow rate is not enough, resulting in the weak shock of the machine.
2、由于长时间震动，会出现以下造型机故障：联接震定台与震击活塞的6条M20内六角钉松动，使震台与活塞之间有间隙，工作气流从此处泄漏，造成震击无力，特别是压实后不能震击。
2. Due to the long time vibration, the following faults will occur in the moulding machine: the six M20 internal hexagonal nails connecting the shaking table and the piston are loosened, which makes the gap between the shaking table and the piston, and the working air leakage from here, resulting in the weakness of the shaking, especially after compaction.
3、活塞与泵铁之间不润滑，发生锈蚀，也可造成震击无力，解决造型机故障，可打开通往震实台的橡胶管，注入一斤左右的煤油或山刷房 保定强夯 卷扬式启闭机 保定网站制作 收费岛模具 遮阳网 麻绳汽油，然后上好，开机震击，这时震击的声响会有很明显的变化。
3. There is no lubrication between piston and pump iron, and rust occurs. It can also cause shock weakness. To solve the problem of the moulding machine, the rubber pipe leading to the shock table can be opened, kerosene or gasoline can be injected into it, and then the sound of the shock will change obviously when the piston and pump iron are not lubricated and rusted
