| 多触头造型机可用于各种铸造车间粘土砂上下箱造型， |
| 添加时间：2023/11/3 16:13:06 浏览次数： |
| 多触头造型机可用于各种铸造车间粘土砂上下箱造型，可以单机使用或组成机械化流水线使用，亦可组成半自动线使用。 The multi-contact moulding machine can be used for moulding clay sand boxes and boxes in various foundry workshops. It can be used alone or in a mechanized assembly line, or in a semi-automatic line. 多触头造型机的特点： Characteristics of multi-contact moulding machine: 1、采用气动多触头压实，没有漏油的困扰；比压适中对型砂无特殊要求，触头数量多（60个）适合于复杂模型造型。 1. Pneumatic multi-contacts compaction is adopted without oil leakage; there is no special requirement for moulding sand in proper compaction, and more contacts (60 contacts) are suitable for complex moulding. 2、本机在压实时，机架不受力，而是由多触头体侧面下垂四根拉杆钩住工作台，随着多触头的向下伸出，进行压实，如果把触头、钩子、砂箱、型板、工作台看成一个系统的话，这种压实力是内力或称内力压实。 2. The machine is pressed in real time, and the frame is not subjected to force, but is hooked by four pull rods hanging from the side of the multi-contacts body. With the multi-contacts extending downwards, the machine is compacted. If the contacts, hooks, sand boxes, profiles and workbenches are regarded as a system, the compaction strength is internal force or called internal force compaction. 3、压震实，触头一方面压实砂型，同时随工作台一起震击（与机架脱离，机架不受震动）。故震击压实效果好，砂型硬度高而均匀（平均硬度达85~90，B型硬度计值），吃砂量可小至20~30毫米，吃砂比达H：B=2~3，且其型腔垂直面的硬度仍可达到80以上。 3. Compression and compaction. On the one hand, the contacts compact the sand mould, and at the same time, they are shocked together with the worktable (separated from the rack, the rack is not Therefore, the shaking compaction effect is good, the hardness of sand mould is high and uniform (average hardness is 85-90, B hardness meter value), the sand consumption can be as small as 20-30 mm, the sand consumption ratio is as high as H:B=2-3, and the hardness of the vertical surface of the cavity can still reach more than 80. 多触头造型机的特点采用弹簧全定送水 保定骨伤骨病 铜鼎铜钟 淤泥固化设备 保定舞蹈 化粪池钢模具 保定网站建设缓冲气动微震机构，故对地基无特殊要求，起模采用连杆同步轴结构，气压油调速，起模同步性好，速度控制自如。 Multi-contact moulding machine features spring full buffer pneumatic microseismic mechanism, so there is no special requirement for the foundation. The moulding adopts the structure of connecting rod synchronous axis, pneumatic oil speed regulation, good synchronization of moulding, and free speed control |
| 上一页 垂直极化基本内容 |
| 下一页 市面上的全自动造型机都是采用液压系统来工作的 |
Copyright © 技术支持：遨游网络